Quick welding update

Just thought I would let my readers know that I have been teaching myself to weld over the last couple of weeks with the MIG lent to me by James Shopland. I have been learning a lot of mistakes and very quickly too, not on the Midget though, just on scrap metal.

I cannot really progress too much further without the necessary skills in place, but I also need some more parts, in and around the rear bulkhead which I am saving up for this month.

I have been cleaning up some of the old metal with flap discs and preparing it for welding. I am trying to cover all types of welds that I need to complete the chassis. These include flat gap, angled gap and pit welding. I will try and post some pictures of my attempts in a few days. 

I bought a new auto darkening welding mask which is brilliant I have to say. But I do need some specialise mole grips to get the job done properly, further cost to this build, but nothing really that others incur thanks to the generosity of my friends and family. 

My stepfather donated a heavy duty vice to help with the metal work, which is very kind of him. It will fit very nicely on my new bench.

Further Test Fitting

Certainly getting closer so welding in some panels now. I have been concentrating on preparing all the edges and making sure that the good metal is all straight to receive the new panels.

I know I have mentioned this before but it is such a good feeling looking at the Midget with shiny new metal in place.

My next stop will be the local metal supplier, where I need to buy some sheet metal so I can make up some new sections. One to go in the front footwell panel, the other to go in the rear bulk head, behind the kick board.

Last weekend we had good weather and as the sun shone it felt like Spring for the first time this year. It prompted us to get in the garden where we had a Spring tidy up, that included a clear out of the summer house which more resembled a city's dump than anything else.

One of the things that had been filling the space in the summer house was a couple of trestle table legs and an old kitchen worktop, which I have put to good use in the workshop. I just now need a bench vice so I can begin my bespoke metal work!

Floor & Sill Repair Preparation Update

Over the Easter break I managed to spend some more time working on my MG. The focus has continued to be removing old metal and preparing the existing panels to be ready to receive the new panels.

I am still working on the offside floor and have now removed enough metal to get a first test fitting on a new floor panel!

On Saturday I also managed to get the new cross member from Moss that I will be cutting to size and welding to the good part of the original.

It is so good to see the new panel in place, it really helps with my confidence and motivation. Drilling out all the spot welds is certainly a labour of love!

The rust damage around the rear bulk head is considerable and I will need to make up some repair sections myself to make good that area.

Floor & Sill Repair Preparation

I have been following many peoples advice when restoring a MG Midget, to take it slowly and concentrate of small sections at a time. This is very important advice, as there is so much metal work to be done and I have to learn many new skills as I go.

Today I tackled the task of removing sections of the rusted floor plan that was originally spot welded to the chassis.

First job though was to buy some ear defenders as recent grinding activities had left me with my ears ringing for hours. I can't tell you how much a difference it made to my concentration. Removing the one sense that was distracting me from the job in hand helped enormously.

Spot weld by spot weld, I drilled each one and removed a small section. These drills holes will act as my guide to puddle weld in the new panel.

It was a relief to see that the inner part of the chassis was relatively free of rust. I will apply some rust remover and finish with black chassis paint before welding on the new floor panel. 

This section though needs some serious work. I would like to repair this with steel cut to size and welded in. Give me a chance to test my very new and raw welding skills.

New Supplies

Whilst browsing through ebay the other day I came across a bonnet (the only part not supplied with the car). It looked in good condition so I kept watch. As the auction end got closer there was only one bid of £10. Knowing that new you can pay £400 for a new one, I though it was worth a go and I was surprised that the bids didn't go much higher, as I won the thing for only £16!

I picked it up from a great guy called John who was having a clear out. He also offered me a box of parts that he was putting together and said that I could pick it up the next time I was passing by. He didn't want any cash for them, he only asked that I made a contribution to the Air Ambulance. So I thought I'd put the link here and see if some of my readers would like to donate as well. Thames Valley and Chiltern Air Ambulance

There are a few minor rust holes that can easily be sorted

This week it was my birthday and family very kindly gave me some more Moss vouchers, so my collection of new panels is coming along nicely!

The First Cut

So now the really scary bit! With angle grinder in hand it was time to start to remove the damaged panels of the MG Midget. I decided to work on the offside of the car, because that side had had work done on it that was of a poor standard. I could also get the measurements needed from the original nearside where there has been no alterations.

I started by measuring every distance that I could and cross referenced it to the nearside. There where some differences caused by the poor patch jobs of a previous owner. After that I had to go for it and work out the best way to get the sills off.

 

So I started to investigate where the inner sill was attached. There didn't seem much...

Then I looked at the A post which was rusted at the base and cutting what I thought was the worst part only hinted that all was not as it seems. The whole panel was covered in filler! There is a large dent running right down the middle of it. So that had to go as well, which didn't leave much for the inner sill to hold on to, except the cross member. 

 

I decided to take stock of the panels I needed and with the vouchers my lovely wife got me from Christmas I popped down to Moss and purchased two new inner sills, two outer footwell side panels and a toe board. I still needed plenty more but for now the outer side panel helped me realise how bad the rust had got. So I cut out it out!

With a little more persuasion both sills came off, along with a section of the cross member and part of the floor!

So I am now left with tidying up the edges to prepare them for the spot welding, but there are more rusted sections on the front footwell panel and triangular support, shown here below.

But I am getting to grips with the metal work and even in this small section things are progressing and I am starting to love flap disks.

I also got the chance to practice some welding for the first time with the help of my 17 year old nephew, who wanted to see what his crazy uncle was up to. He thought it was 'Sick Man!'

One or Two New Panels Required

So now that I have removed all of the patches that a previous owner had decided at the time was a good idea to cover up the rust, I can now see the full extent of the MG Midget project that I have sitting in the workshop. The only good thing to say is that my grinding skills have improved dramatically!

The offside rear wheel arch seems to be the worst area leading me to think that I am best off replacing the entire boot floor.

Other areas were as bad as I had imagined...

I believe the general consensus is to start with the outer side panels, sills and cross members. Then I will need to work on the lower A post and door hinge.

Small steps!! 

Metal work begins

Last night I packed away my spanners, socket set and WD40 for the simple reason that there are no more items to remove off the chassis. As of today I consider the restoration work to have started, just short of 3 months since the Midget was rolled into the workshop.

My next task will be to take measurements of the chassis to make sure that during the metal working I retain or in some cases return the chassis to its original specification.

For example, I have measured the door span on both the near and off sides and on the off side where the a previous owner has made an attempt to repair the sills, the gap is 0.5 cms smaller than the near side, which explains why the door doesn't shut properly!

Once I have confirmed the alignment of my chassis I will then start to cut out all of the patch welding to expose the rust behind. From there I will be focusing on the sills, outer side panels and the bottom of the A posts. The floor will follow along with rear bulk head repairs.

Certainly got my work cut out!! 

Suspension Removal Update Continued....

Last night I managed to grab a couple of hours in the workshop and successfully removed the axle.

That did though give me a chance to look under some of the patch welding that seems to be dotted here and there. More tests for my welding skills!!

Also I think new springs might be required...

Suspension Removal Update

Tonight I have finished removing the front suspension. I will start on the rear hopefully later in the week.

Underseal removed

Unfortunately I didn't manage to get as much time in the workshop as I had previously planned over the holiday period, apart from a few hours on New Years Eve.

Now that I am getting closer to start replacing the damaged sections of chassis, I wanted to find out the true condition of the floor from the underside of the car. This meant I needed to remove all the underseal, which was fairly thick in places, as you can see from this photo. I had asked a few people about best methods which ranged from hair dryers and heat gun paint strippers to go old fashioned elbow grease.

So I tried the hair dry first, but there just wasn't enough heat to help shift it and to be honest where it did have an effect the underseal just turned to thick toffee which was making a mess.

I then had a idea. When I bought the car there was an old wooden handled chisel in the footwell. You can see it here in the photo next to the door. At the time I asked Kim Dear if he wanted to keep it. He said it wasn't his and I was welcome to it. As the underseal was quite hard I wondered if the chisel would be a better tool.

I couldn't believe my luck as within two hours I had cleared all the underseal from the underside of the floor and engine bay sections.

                             Click on images to enlarge

This now gave me the ability to make a decision on what repairs I needed to make. Although the vast majority of the metal was in very good condition, the areas where rust is commonly found is quite bad. Particularly in the key areas where the strength of the chassis is crucial.

Looking at these photos makes me think that the best approach is to completely replace the floor section as a whole. Even though there are repair sections that will replace the rusted areas, the amount of cutting and welding could easily exceed the amount required for the entire floor, especially with that bloody big hole a previous owner decided to make in the middle of the drive shaft housing. It will also expose areas that are currently inaccessible to check for further problems. 

I think it is time to start ordering new parts!!