After many hours of alignment preparation I decided to bite the bullet and weld the outer sill into position. I chose the lower contact points first just in case there was any metal warping that I might to able to correct in the top of the sill.
First off I needed to clean up each weld using my mini wire brush attachment.
After that I clamped around each hole and used a pick to ensure that no primer and only bare metal was exposed to ensure a clean weld. I made sure that every weld was completed at a different points on the sill to reduce overheating and warping.
Quit impressed with some of these welds. Funny how some go so well and others end up with too much metal in them.
Next job is to check the door alignment and complete the welds in the top of the sill. I will need to make sure there are no gaps around the sill which might let moisture in. Then grind it all down smooth and paint it to protect the section until it is time for the soda blasting!
Follow my project of restoring a 1965 MK II MG Midget classic car. This will be a complete rebuild restoration.
Monday, 30 January 2017
Saturday, 28 January 2017
Outer Sill Alignment
In order to make sure I get this outer sill aligned to the best of my ability I consulted with my friends at the MG Cars Enthusiasts' Club. They, as always gave me some valuable advice which was to properly line up everything first and make sure that the door looked good.
But there was one job that I have been putting off for some time, not for any particular reason other than I was just nervous about cutting more metal away from the A post pillar.
The problem I have with this repair is the repair panel itself. I have noticed that the new panel is slightly smaller to the lower left of the hole where the windscreen support slots into. I guess that is something I will have to tackle at some point.
For now I needed to cut some metal away so that the A-post panel will fit in place so I can test fit the door, the wing and the A-post to make sure the outer sill is in position and ready for welding.
But there was one job that I have been putting off for some time, not for any particular reason other than I was just nervous about cutting more metal away from the A post pillar.
The problem I have with this repair is the repair panel itself. I have noticed that the new panel is slightly smaller to the lower left of the hole where the windscreen support slots into. I guess that is something I will have to tackle at some point.
For now I needed to cut some metal away so that the A-post panel will fit in place so I can test fit the door, the wing and the A-post to make sure the outer sill is in position and ready for welding.
Oh look more rust! Hardly surprising as this spot it a usual suspect in terms of rusting points. I'll be back to sort you out later, but for now it was time to check the alignment.
I think that it all looks fairly good for a test fitting. I am happy with the gaps as they all seems to be constantly equal and straight. Hopefully I can start to tack some welds in tomorrow.
Wednesday, 25 January 2017
Outer Sill Preparation
For the last couple of evenings I have been preparing the outer sill for one of my most nervous welds to date. If I get this wrong it could ruin the entire look of the car.
Gaps, wheel arches and bolt holes all have to be carefully considered to ensure I don't mess this up.
First job is to prepare the inner sill that is going to be covered for evermore (hopefully! Not doing all this again in a hurry) by painting it in a couple of coats of black chassis paint to protect it from the rust.
Finally the outer sill in (hopefully) in position ready for welding.
Gaps, wheel arches and bolt holes all have to be carefully considered to ensure I don't mess this up.
First job is to prepare the inner sill that is going to be covered for evermore (hopefully! Not doing all this again in a hurry) by painting it in a couple of coats of black chassis paint to protect it from the rust.
Then I drilled all the weld holes in the outer sill, took it back to bare metal and sprayed the edges with weld-through primer to protect the join from rust. I applied a couple of coats of chassis paint to the inner section, as shown below.
Next I presented the outer sill to the inner sill and sprayed a little primer through the holes to highlight the welding line.
This was then stripped back to bare metal and sprayed with weld-through primer.
The gaps and arches all look good, including the two ends of the outer sill which I was relieved to see ends perfectly in-line with footwell end and the rear bulk head. Must have done something right! In case you are wondering why the blue wing, the guy I bought the MG Midget off included it in the price as the old one was too far gone.
Next post will be welding in the sill and then on to the A and B post repairs and fitting the door.
Tuesday, 17 January 2017
Where does the time go
It has been a long while since my last post, but I have been somewhat busy working on the house that we bought nearly two years ago. Every room and the garden needed to be redone. During the summer I spent nearly all my time working in the garden trying to transform it from a jungle to something we can enjoy as a family. During the winter months to date I have been sorting out the bathrooms. I'm happy to say that I decided that enough was enough and it was time to get back to the MG!
There was a couple of things that encouraged me to get back it, the first was watching quite a few episodes of CarSOS, kind of hoping that I would appear on the show, only to get frustrated that it wasn't me and telling myself I must get back into the garage. The other was some nice gifts friends and family gave me for Christmas.
My last post explained about getting ready weld in the floor. Well I am please to say that I completed that job back in the summer. I just don't think I took any photos. My next job is to align the outer sill and prepare the area for its fitting.
I am so happy that the sill and the wing appears to line up really well. The b-post repair also looks like it should fit into place with near perfect gaps all round.
There was a couple of things that encouraged me to get back it, the first was watching quite a few episodes of CarSOS, kind of hoping that I would appear on the show, only to get frustrated that it wasn't me and telling myself I must get back into the garage. The other was some nice gifts friends and family gave me for Christmas.
My last post explained about getting ready weld in the floor. Well I am please to say that I completed that job back in the summer. I just don't think I took any photos. My next job is to align the outer sill and prepare the area for its fitting.
I am so happy that the sill and the wing appears to line up really well. The b-post repair also looks like it should fit into place with near perfect gaps all round.
Subscribe to:
Posts (Atom)