Another major win on the MG Midget project, welding in the outer sill. It doesn't actually take that long to weld in place. It is the all the prep work that needs to be done first.
Drilling the holes for welding, painting the sections that will be hidden forever. Making sure that the contact points are painted with weld though primer. And then there is the measuring and alignment, which seems to take forever, but is totally worth it because if you get this part wrong it will have a massive knock on effect that could ruin the door alignment.
Follow my project of restoring a 1965 MK II MG Midget classic car. This will be a complete rebuild restoration.
Tuesday, 24 September 2019
Wednesday, 21 August 2019
LHS Outter Sill Alignment
With work progressing well on the engine bay of my Mg Midget I felt it was time to start planning the installation of the outer sill on the left hand side. This meant fitting the donated wing, which went well and all lined up nicely. Trying to fit the door as best as I could considering the state of the A-post and then offering up the outer sill.
At first glance it was looking good, especially around the front and rear wheel arches. But I noticed that the gap under the door was slightly to big and also there was an ever increasing gap between the front wing, a-post and door.
The top of the door is aligned correctly, so I am thinking it is the b-post that needs to be altered that will allow the sill to come up a little at the rear and so close the gap, because the bottom of the door doesn't sit right.
As the B-post skin isn't in great condition and as I have a repair panel, I'll cut this out and get the sill aligned to the door and build the A and B posts around it.
Plenty to be getting on with!
At first glance it was looking good, especially around the front and rear wheel arches. But I noticed that the gap under the door was slightly to big and also there was an ever increasing gap between the front wing, a-post and door.
The top of the door is aligned correctly, so I am thinking it is the b-post that needs to be altered that will allow the sill to come up a little at the rear and so close the gap, because the bottom of the door doesn't sit right.
As the B-post skin isn't in great condition and as I have a repair panel, I'll cut this out and get the sill aligned to the door and build the A and B posts around it.
Plenty to be getting on with!
Tuesday, 20 August 2019
Front Wheel Arch Repairs
Managed to get round to the front right wheel arch this evening which needed a simple repair. Rust had got behind the join that had gone right through.
There are a couple more areas that need attention as shown below. you can just about see the flaps raised a little due to rust underneath, but I am hoping they are not as bad as the one above. I am planning on drilling out the spot welds and bending the flaps back, cleaning it all up and then welding them back down again.
And so the work begins
There are a couple more areas that need attention as shown below. you can just about see the flaps raised a little due to rust underneath, but I am hoping they are not as bad as the one above. I am planning on drilling out the spot welds and bending the flaps back, cleaning it all up and then welding them back down again.
Tuesday, 23 July 2019
Battery Tray Completed
My biggest worry was that I was going to have to replace the whole section which was way more complicated than what I had planned. Fortunately it did go to plan.
First job was to check to see where the bad metal stopped. On closer inspection I realised I did need to cut more from the back wall.
I just wasn't happy with the pitting. That needed me to drill out some more spot welds the from other side and then cut back to good metal.
Next job to clean up all the waxoil as best as I could, which took a while using a brush and lots of Gunk degreasing agent. But it did evenually come off with a load of elbow grease as well.
The flanges that the tray sits on needed to be made good before I could weld the tray on.
Next was to make the template and offer it up.
And finish with primer.
Really happy with the results. Also managed to fix that hole above the tray. I think next stop will be the footwell toe panel.
Tuesday, 9 July 2019
Battery Tray Repair
I don't know why but I have been looking forward to working on this repair for ages. Probably because it is always right in my face looking at me from the front of the car.
The battery tray is really badly rusted.
I needed to cut out the worst of it in the hope I can weld in a new panel, without having to replace the whole section.
So far so good! Just need to clean this all up and cut out a new piece of metal and weld it in, but with all that waxoil that someone has painted on there I'll have to wash it down first with degreaser or the welds will become decontaminated.
I will also have to sort out this little hole as well.
The battery tray is really badly rusted.
I needed to cut out the worst of it in the hope I can weld in a new panel, without having to replace the whole section.
So far so good! Just need to clean this all up and cut out a new piece of metal and weld it in, but with all that waxoil that someone has painted on there I'll have to wash it down first with degreaser or the welds will become decontaminated.
I will also have to sort out this little hole as well.
Thursday, 4 July 2019
Nearside Triangular Support
I remember when I first got to look over my MG Midget and thought at least the nearside triangular support isn't as bad as the other.
In some ways I wasn't wrong, but just because it didn't look like this...
... doesn't mean it will be a quick fix.
Ultimately I found some rust and if I don't deal with it now it will bother me for the rest of time. So that mean't pretty much the same amount of work as before.
I think this is the only photo I have of the nearside when I first stripped the car and you can see it looks in much better condition than above. There is just a small rust patch in the bottom right corner which I thought would clean up.
but it turned out to have a few small holes!
Now that was all taken care of and back to good metal I could get on with the main structure.
But then I had to deal with the badly fitting repair panel.
In some ways I wasn't wrong, but just because it didn't look like this...
... doesn't mean it will be a quick fix.
Ultimately I found some rust and if I don't deal with it now it will bother me for the rest of time. So that mean't pretty much the same amount of work as before.
I think this is the only photo I have of the nearside when I first stripped the car and you can see it looks in much better condition than above. There is just a small rust patch in the bottom right corner which I thought would clean up.
but it turned out to have a few small holes!
It was at this point I decided to repeat the same job as before, which meant starting with the end panel.
But then I had to deal with the badly fitting repair panel.
That needed the same alterations as before.
I don't know why heritage have made the panel that don't fit but my local Moss supplier assured me they have always been like that. At least this time I knew what I was doing!
There were a few more welds to make good to seal it all in correctly and make a replacement splash plate that was previously damaged, so now it should last for many years to come without me worrying about that rust!
Subscribe to:
Posts (Atom)