Monday 6 April 2020

Door Repairs

Over the past few weeks I have been working on various sections of the chassis, tidying up areas that I had either not completely finished or had missed. Most of these are small little jobs that needed welding and making good. I also completed the outer sill end on the rear wheel arch. Certainly not worth another post, but they can be awkward to finish off neatly!

Having finished the rear wing and wheel arch I wanted to check the gaps again around the door and the front wing. After fitting I remembered that there was some filler present on the bottom of the door. 

After removing all the filler this is what I discovered!



I thought it best to cut out the worst parts back to good metal.





The rust had worked its way into the main door structure, but much of it was surface with some pitted metal.

But once it was all cleaned and the holes welded up, with a few coats of rust converter it started to look good again.



Then with the primer to seal it up.



Just needed to make a new panel



And start to weld it in.


And finish up.


Now for the bottom left


Template ready


Think it will fit in there


Trying to keep the amount of heat to a minimum to reduce warping of metal


Although the photo looks ok across the bottom half where I have welded, there was significant warping. Many people warned me of this. I had read up on metal shrinking techniques that help pull the metal together to reducing the warping by tightening the metal. I tried it here with a blow torch and a very damp rag. Heating up the area you want to shrink, but only a little. You don't want the metal to blacken if you can. Then you apply the damp rag to cool the area and this shrinks the metal and helps correct the warping.

I think I will need more filler here than I planned but as long as everything looks straight I'll be happy. Which it is.

Monday 2 March 2020

Right Rear Wing Repair

Time to complete one of the last major sections on the chassis on my MG midget.

The rear wing on the right hand side had some particularly interesting repair sections.


 

It has been some months now since I completed the wheel arch and floor panel so this left me with a good starting point to work from. First job was to offer up the repair panel and mark out the cutting line.



When it was all looking right and aligned it was time to cut the old metal out.



There is some rusty metal on the lower end of the downward curve of the wing that will need to be cut out and replaced. I will also need to weld up the holes and any joints that are exposed to moisture creeping in. Then I need to prepare all the metal in this area with protective paints as there will be parts the sandblaster can't get to. 

The repair panel seems to offer up nicely. So quite a bit more prep work and then we're good to weld in.



Here are some photo's of the repair to the lower downward curve. Should be ready to attach a flange that the rear wing panel will attach to.



This gives me the chance to make up a bespoke repair again. There wasn't much of a template left.



All cleaned up and we're ready to weld in the rear wing panel!


I have always been really worried about warping the metal on these outer panels. It is really important to make sure that they don't warp outwards as they can cause the whole panel to look out of shape that no amount of filler will ever fix. The way that I have found works reasonably well is to take your time and not weld in one place for more than a second. That way you don't build up too much heat in the panel which can cause the distortion.

I think this repair panel has come out just fine.


There are a few small areas that need tidying up but I think that finishes off this section, which means I have only two areas left on the main chassis and that is the front chassis legs and the sill ends on this right hand side. After that it's the doors!

Saturday 1 February 2020

Front Chassis Plate

When I first looked at the damage to the plate on the underside of the front chassis I was genuinely worried about the possible extent of rust that most certainly lay in wait for me.



It is difficult to tell from the photo but this panel was really beaten in and bent back with gaps to let water in and so most certainly create rush behind.

The original plan was to make a new shiny new replacement for this. I decided to use this old panel as a template.



After cleaning up the surface the metal was in good condition, apart from the dents.

I set about drilling out the spot welds to remove this panel.

Amazingly once I had done that and removed the panel I really couldn't believe how little damage was behind. Almost none!



The plate itself needed a good clean and hammer. But i thought that if it came up good enough, why not just prepare it and weld it back in.



First job was to prime the box section. 



Then hammer time!



Gave it a coating of weld through primer and the following day after it had dried, welded it in.



Apart from the chassis leg ends or front end support that is the underside of the car finished!

Tuesday 10 December 2019

Sill End Repairs

Getting closer now to finishing off the left hand side of the chassis now.

Just got to tackle these tricky little sill end finishers. 



The one thing you have to keep reminding yourself is that this area is so prone to rusting due to water get into the sill. So I needed to make these sill ends as watertight a possible, but also ensure that they fit smoothly, so not to remove the primer. Not easy and takes a lot of small adjustments before welding it all in the set position and drilling the welding holes and spraying on the weld-through primer.




I have been preparing the other three areas as well all in the same fashion.